Home » News » Industry News » What is a shop press used for?

What is a shop press used for?

Views: 2     Author: Site Editor     Publish Time: 2020-12-18      Origin: Site

The shop press is a kind of general press with exquisite structure. It is widely used in cutting, punching, blanking, bending, riveting and forming, etc. So what is a shop press used for?

What is a shop press?

The use of the shop press

What is a shop press?

The shop press has the characteristics of wide application and high production efficiency. The press can be widely used in cutting, punching, blanking, bending, riveting and forming, etc. By applying strong pressure to the metal billet, the metal is plastic deformed and broken to produce parts. When the mechanical press works, the large pulley is driven by an electric motor through a triangular belt, and the crank slider mechanism is driven by a gear pair and a clutch, so that the slider and punch go down in a straight line. Upon completion of the forging work of the mechanical press, the slider will go up and the clutch will disengage automatically. At the same time, the automatic device on the crank shaft will be connected to make the slider stop near the upper dead center.

The shop press machine is driven by a motor through a driving mechanism to exert technological force on the work piece. The transmission mechanism is a belt transmission and gear transmission reduction mechanism; The working mechanism is divided into screw mechanism, crank connecting rod mechanism and hydraulic cylinder. There are three kinds of shop presses: screw press, crank press and hydraulic press. Crank press is also called mechanical press. The screw press has no fixed lower dead point. It can be hit and formed for many times for large die forging parts. It can be used for single, consecutive and inching. The impact force is related to the deformation of the work piece. The impact force is small when the deformation is large, and large when the deformation is small. It is similar to a forging hammer in these respects. However, its strike force is closed through the frame, so it works smoothly and vibrates much less than a forging hammer, which does not require a large foundation. The lower part of the shop press is fitted with forging ejector. The screw press has the functions of various forging machines, such as die forging hammer and mechanical press, etc. It is versatile and can be used in die forging, blanking, drawing and so on. In addition, screw press structure is simple, easy to manufacture, so it is widely used.

shop press

The use of the shop press

Improper shop press operation or die setting is the primary cause of press damage and shutdown. Proper training of press operators and die setters ensures that they follow the correct procedures. This will quickly reduce downtime.

1, Lubricating oil is poured into the rotating shaft of brake at each point of the forward manipulator on each shift. The appropriate amount of no. 20-30 mechanical oil is filled with the oil gun at the head of the rod and ball every day before the shift. Lubricating oil is pressed with the oil gun at the clutch every day before the shift. Clean the machine before every shift stop.

2, Check the fasteners and make up the missing parts. Check the clutch and spring and belt. Check the lubrication devices of the machine tool. Check electrical wiring damage, aging, motor, electromagnet is normal. Inspect crankshaft guide for accuracy and wear. Check brake, clutch, slider, closing block, closing ring. Check the electrical control section. Check and adjust the connecting bolt of fuselage table.

According to different types of press machines and processing requirements, formulate specific, practical safe operation procedures, and carry out necessary job training and safety education. The user and operator must strictly observe the provisions and operating procedures of the safe use instructions provided by the design and manufacturing unit, and correctly use and overhaul the equipment. General safety operation requirements of press are as follows:

1, Before moving the equipment, check whether the operation part, clutch and brake of the press are in effective state, whether the safety protection device is complete and easy to use, whether there are any abnormal parts of the crank slider mechanism. If any abnormality is found, necessary measures should be taken immediately. It is not allowed to operate with disease. Disassembly and damage of safety devices are strictly prohibited. Before the formal operation, it shall go through idle test and confirm that all parts are normal before working. Before starting the machine, all unnecessary items should be cleaned up on the work table to prevent people from being injured by vibration or the sudden start of the slide block caused by the impact of the switch. Tools must be used in operation. It is strictly prohibited to directly reach into the die mouth to retrieve objects. Manual tools are not allowed to be placed on the mold.

2,When adjusting the position of the work piece in the die area or unlocking the work piece stuck in the die, the foot must leave the pedal. Multiple people operating the same press should be unified command, clear signal, the other side to give a clear response, and confirm to leave the danger area before action. The power should be turned off after a sudden power failure or operation, and the manipulator should be restored to the neutral clutch, and the brake should be in the braking state. When repairing and adjusting the press machine and installing, adjusting and disassembling the mould, it should be done when the machine tool is disconnected from energy (such as electricity, gas and liquid) and the machine tool stops running, and it should be supported reliably by adding pad blocks under the slider. Warning notice at the start switch of the machine.


This is the purpose of the shop press, through this article you can know the specific purpose of the shop press, let the shop press play its role.

Related Products

content is empty!


+86 57189935095




+86 13958159228



  • [Industry News] Working principle of hydraulic jack

    In principle, the hydraulic jack is based on Pascal principle, that is, the pressure of the liquid is the same everywhere, so in a balanced system, the pressure exerted on the smaller piston is relatively small, and the pressure exerted on the larger piston is also relatively large, which can keep t


Sign up for our newsletter to receive the latest news.
​Copyright © 2020 Hangzhou Omega Machinery Co.,Ltd. All Right Reserved  Sitemap